Att 7630 Uživatelský manuál

Part 2Please read Part 1 — Important Product Information,included in your package.User's Manual forCordless DigitalAnswering SystemSpeakerphone 7

9HoldPress H to put a call on hold. The PHONE light on the handset flashes.To return to the call, press H again— OR —Press P on the handset— OR —Pres

10Handset LocatorThis feature is useful if you misplace the handset.To locate the handset using this feature, press and hold the INTERCOM/HAND-SET LOC

11TELEPHONE MEMORYAt the HandsetThis cordless answering system can store 20 different phone numbers that you dialby pressing p and two of the number b

12TELEPHONE MEMORYAt the HandsetStoring a Number Just DialedWhenever you make a telephone call, you can store the number you dialed inmemory. Press R

13Answering a CallTo answer using the Speakerphone, press K on the base. The SPEAKERlight goes on, and the call is connected. To end the call, press

14This cordless telephone answering system operates at the maximum power al-lowed by the Federal Communications Commission (FCC). Even so, the handse

15Turning the System On/OffThe answering system must be on in order to use any answering system functions.When the answering system is on, the Message

16Announcement OptionsBefore using this answering system, you can record an announcement (up to 3minutes long) that callers will hear when the system

175 When you are finished, press S. The system plays back theannouncement, and the Message Counter displays AP (AnnouncementPlay). If the announceme

18Audible Message AlertIf you want the base to beep once every 15 seconds to notify you that new messageshave been received, set the Message Alert to

1CONTENTSINSTALLATION ...2Table/Desk Installation ... 5For Wall Installation ...

19Changing the Priority Calling CodeThe priority calling code comes set to 999, but you can change it to any three-digitnumber from 500 to 999 followi

20Answering CallsWhen you’ve selected Announcement A or B and turned the system on, the callerhears the announcement you recorded, followed by a beep.

21Listening to Your MessagesAs the system plays back messages in a mailbox, the Message Counter displaysthe number of the message playing. Before pla

22ANSWERING SYSTEM OPERATIONAt the BaseDeleting MessagesDelete all messages in a mailboxPress and release D, then press the l button of the mailbox yo

23This cordless answering system allows you to retrieve messages and access otherfeatures even when you are away from your home or office. Additional

24Remote Access CommandsPlaying Messages1 Connect with the answering system.2 After the two beeps, wait 4 seconds. The system plays back messagesin M

25Call ScreeningYou can uses the cordless handset to listen to callers as they leave messages. Youcan speak to a caller by pressing P.To monitor a cal

26ANSWERING SYSTEM OPERATIONAt Cordless Handset or Touch Tone PhoneRemote ON/OFFReview ON/OFF StatusConnect with the answering system. Press ). The sy

2711 The system announces the Priority Calling Code, followed by "Toselect the first digit, press 6 or 4, then press 9."12 Follow Step 10 to

28The handset batteries need charging when:• The phone beeps four times when you press P.• The INTERCOM/LOW BATT light on the handset is on when the p

2INSTALLATIONPut caller on holdStore and accessnumbers intelephone memoryChange channelRedial last number calledAnswer page from baseAdjust listening

29Replacing the Handset Battery Pack1 Remove the battery compartment cover on the handset by pressing onthe indentation and sliding the cover downward

30If you have difficulty operating this telephone answering system, try the sugges-tions below. If you still have trouble, call 1 800 722-9125.If the

31IN CASE OF DIFFICULTYIf you hear noise or interference when using the phone• You may be out of range. Move closer to the base.• Press h to change t

32IN CASE OF DIFFICULTYIf messages are incomplete• If a caller leaves a very long message, part of it may be lost when thesystem disconnects the call

Cordless Digital Answering SystemSpeakerphone 7630ANSWERING SYSTEM OPERATION1 Dial telephone number and wait forsystem to answer.2 Enter Remote Access

Play all messages 1, then mailboxin mailbox numberPlay new messages2, then mailboxin mailbox numberSave messages Hang upDelete message being played 3D

3INSTALLATIONUse with other buttonsto change settingsRecord/reviewoutgoing announcementSet/hear day & timeSet answeringsystem featuresStop message

4!INSTALLATIONModular jackPower cord Telephone line cordStandardelectricaloutletKeep baseantennaupright.7630_book.1AT&T 8/12/98, 6:28 PM4

5Table/Desk Installation1 Choose a spot near an electrical outlet and a telephone jack.This phone requires a modular telephone jack and a standard ele

6NOTE: When the system is first connected to AC power, it begins an automaticinitialization routine. After this routine is complete, the Message Cou

75 Feed the free end of the line cord through the rectangular openingin the center of the bracket.6 Replace the bracket.Place the bracket back on the

8Making a Call1 Press P on the handset (the PHONE light goes on).2 When you hear a dial tone, dial the number.Answering a CallIf the handset is in th