Att 9230 Uživatelský manuál

900 MHz Cordless Telephonewith Caller ID/Call Waiting 9230Please also readPart 1 — Important Product InformationUSER’S MANUAL Part 2AT&T and the g

9TELEPHONE OPERATIONPage/Handset LocatorPress once to pagethe handset for upto one minute— OR —Press twice to cancel.On steadily when handset is in us

10TELEPHONE OPERATIONHeadset JackYou can use this telephone hands-freewhen you install a 2.5 mm headset(SKU 24099), purchased separately.Plug the head

11TELEPHONE OPERATIONDisplay Screen MessagesScreen Displays: When:STANDBY The handset is not in use.NO LINE The base is not connected to the telephone

This cordless phone can store 50 telephone numbers with names, each upto 16 digits long.Store Memory Numbers1 Make sure the handset is off.2 Press M.

13Edit Numbers Stored in Memory1 Press < to review numbers stored in memory.2 Press when the screen displays the number you want to edit.EDIT flash

14Dial Memory Numbers1 Press P.2 Press M, then enter the memory location (01-50)3 Press .— OR —1 Press < (DIR) to begin reviewing numbers stored in

CALLER ID OPERATION15EnterCaller IDrecords.Reviewnumbersstored intelephonememory.Saveselectionswhen storingnumbers inmemory.

16About Call HistoryThis phone assigns each incoming call a number from 1 to 50. The mostrecent call will have the highest number. When the memory is

HEADLINE RIGHTHEADLINE R-SUB17CALLER ID OPERATIONDelete Call HistoryDelete a Specific Call1 Press > until the screen displays the call information

18CALLER ID OPERATIONStore Call in Memory1 Press > until the screen displays the call information you want to store.2 Press twice.3 Press to store

© 2001 Advanced American Telephones. All rights reserved.Printed in China. 850005851 Issue 1AT&T 1/01

19CALLER ID OPERATIONCall BlockThis feature works with service available from your phone service providerto prevent your call information from being s

20Display Screen MessagesScreen Displays: When:PRIVATE NAME The other party is blocking name information.PPP The other party is blocking number inform

HEADLINE RIGHTHEADLINE R-SUB21Charging the Handset Battery PackThis battery should remain charged up to six days with the ringer turnedon and up to 12

22BATTERIESReplacing the Handset Battery Pack1 Remove the battery compartment cover on the handset bypressing on the indentation and sliding the cover

HEADLINE RIGHTHEADLINE R-SUB23IN CASE OF DIFFICULTYIf you have difficulty operating this phone, try the suggestions below.For Customer Service, visit

24IN CASE OF DIFFICULTYIf you hear noise or interference when using the phone:• Make sure the base antenna is fully upright.• You may be out of range.

CONTENTS1BEFORE YOU BEGIN . . . . . . . . . . . . . .3About Caller Identification . . . . . 3INSTALLATION . . . . . . . . . . . . . . . . . . . . .

BEFORE YOU BEGIN3About Caller Identification (Caller ID)This product has a Caller ID with Call Waiting feature that works withservice from your local

INSTALLATION4Before You Installb) Plug battery packconnector intohandset. Use onlyAT&T battery 3301(SKU#91076).d) Replacecover bysliding it upinto

5INSTALLATION3 Charge the handset battery.Place the handset in the base. Charge the battery for at least 24 hoursthe first time.4 Check for dial tone.

INSTALLATION6Wall Installationa) Align holes onbase withmounting studson wall jack.b) Place powercord as shown,so it hangsstraight downbetween baseand

7Time/Date1 Press G until the screen displays2 Press . The month flashes.3 Use < or > to select the correct month.4 Press .5 Repeat Steps 3 and

8TELEPHONE OPERATIONEnd a CallPress O— OR —Place handsetin baseExit programming.Cancel a page.HoldPress to put a call on hold. Press againto release h